chemical agents to be utilized:
10% heptyl (unsymmetrical dimethylhydrazine) water solution,
heptyl (unsymmetrical dimethylhydrazine) vapour with 0.8 to 1.0 kg/m3 concentration,
10% azotic (nitric) acid water solution,
azotic (nitric) acid vapour with concentration up to 1.1 kg/m3;
2. neutralization method: thermal decomposition;
3. neutralization temperature: +800?C to +1200?C;
4. performance:
? vapour capacity: 70 to 200 m3/h,
? water solution capacity: 50 to 500 l/h;
5. inlet pressure: up to 2 bars;
6. automatic control system;
7. overall dimensions shall allow for mounting the unit on a vehicle chassis.
medical waste incinerators manufacturers General Specifications
6mm plate steel sheel construction
11cm 1400 o C Refractory L iner
Temperature controlled Burners
Secondary combustion Burners
Interlock Switch on Load Doors
Separate Ash Door
One Second secondary Residence @ 1000 o C
400 ° C Silicone Based Paint Finish.
Alloy Temperature Sensor
Factory wired and tested
Capacity-20 kg / hr
Primary Chamber-1607 L
Hearth Area-1:36 sq. m
Secondary Chamber-694 L
Primary Burner (oil)-420,000 btu
Secondary Burner (oil)-900,000 btu
secondary Combustion-1/6 hp
Exhaust Stack-46cm x 6m
Electrical Service-220/50
Weight System-5.700 kg
Dimension “D”-152cm
Load Port Height- 60x 60 cm
Ash Port Height -36 x 36 cm
Blog
INCINÉRATEUR DE PYROLYSE pour déchets médicaux
CARACTÉRISTIQUES TECHNIQUES: INCINÉRATEUR PYROLYTIQUE
| Paramètre | Conformité |
| Type de déchets | Pour traiter les déchets médicaux, catégories A, B, C, D, E |
| Type d’incinérateur | Pyrolytique |
| Taux de combustion nominal | 50 t0 60 kg / h à 3500Kcal / Kg |
| Chargement | Manuel, chargement par lots |
| De Ashing | Décendrage par lots automatique ou manuel |
| L’incinérateur doit éviter le dégagement de fumée noire et de poussières fines pendant le chargement | |
| Capacité de la chambre primaire | 2-3 m³ |
| L’isolation de la chambre de combustion doit être composée de briques réfractaires, ayant une teneur plus élevée en aluminium et isolant, | |
| La plaque de combustion en carborundum évitant la fixation du verre et des scories | |
| Heures d’ouverture / jour | > 10 heures |
| Températures de fonctionnement maximales | 1400 ° C |
| Températures normales de fonctionnement (primaire) | > 850 ° C |
| Température de fonctionnement (secondaire) | > 1100 ° C |
| Il devrait avoir un régulateur de température numérique (régulateur de température dans la montre numérique) | |
| Teneur en carbone des cendres | <2% |
| L’installation doit être totalement exempte de fumée visible et d’odeurs désagréables | |
| Temps de séjour dans la deuxième chambre | 2 secondes minimum |
| Le diamètre intérieur de la cheminée | : Ø 400 |
| Hauteur de pile | > 8m |
| Fonctionnement du brûleur | Marche / Arrêt automatique |
| Le carburant | Diesel |
| Consommation de carburant à capacité raed | > 7kg de déchets / ltr |
| La consommation d’électricité | <2 kW à puissance nominale |
| Tension de fonctionnement | 220 à 240 V CA 50 Hz |
| Des pièces de rechange | Fourniture pour 1 an en option |
| Consommables | Fourniture pour 1 an de fonctionnement à mentionner en option |
| garantie | Assistance pièces et service: 1 an minimum après la mise en service |
| Service après vente | <72 heures |
| Conformité aux normes d’émission | BS3316 ou norme équivalente |
| Système de filtrage de processus | Scruber à mentionner en option |
| Conformité de fabrication CE | BS EN 746-2-1997 |
| Spécification de conception | Type A, B, C, D et E de déchets médicaux |
| Installation et mise en service | Inclus dans l’état de livraison |
| Formation à la maintenance préventive et curative et à l’utilisation de l’incinérateur | Formation des opérateurs incluse dans l’offre |
| Capacité à traiter le plastique | Pas moins de 40% en poids |
Мобильные инструменты для кремации
Макет
CA-200
Картина
Скорость горения
Обычные 100 кг / час
Камера для сжигания ключей
2000 литров
Дополнительный горящий дымовой вал
да
Настройка подачи
Путеводитель
Напряжение
220В
Мощность
3,0 кВт
Вид топлива
Дизельное топливо
Нагреватель
Италия Оригинал
Использование масла (дизельное топливо)
Нормальный 53 кг / час
Внутренние размеры
230 x 100 x 90 см (камера для ключей)
Внешние размеры
290 x 200 x 170 см (трюковая камера)
Экран температуры
да
Возможность масляного контейнера (если нефть газ)
500 литров
Открытие двери
90 х 90 см
Размер дымового вала
5.0 Метров
Тип дымового вала
Нержавеющая сталь
Вес гаджетов брутто
9000 кг (с контейнером)
Технические характеристики процедуры
Уровень температуры в основной камере
800 ℃ –– – – 1000 ℃
Уровень температуры 2-й камеры
1000 ℃ -1200 ℃
Время проживания
2.0 сек.
Горящая производительность
> 98%
Отходы с более низкой теплотворной способностью
3000 ккал
Телефон: + 86-25-8461 0201
Сайт: www.hiclover.com
Электронная почта: [электронная почта защищена]
Электронная почта: [электронная почта защищена]
2020-03-22
Medical Waste Incinerator HICLOVER TS10 PLC 10kgs per hr
|
Items/Model |
TS10( PLC) |
|
Photo |
|
|
Melt Rate |
Typical 10 kg/hour |
|
Feed Ability |
Standard 20kg/feeding |
|
Control Mode |
Programmable Logic Controller( PLC) Panel |
|
Combustion Chamber |
100L |
|
Interior Dimensions |
50x50x40cm |
|
Second Chamber |
50L |
|
Smoke Filter Chamber |
Yes |
|
Feed Mode |
Handbook |
|
Voltage |
220V |
|
Power |
0.5 Kw |
|
Oil Consumption (kg/hour) |
average 8.4 kg/hour |
|
Gas Usage (m3/hour) |
standard 10.1 m3/hour |
|
Temperature level Screen |
Yes |
|
Temperature Defense |
Yes |
|
Oil Storage Tank |
100L |
|
Feed Door |
30x30cm |
|
Smokeshaft |
5 Meter |
|
Smokeshaft Kind |
Stainless Steel |
|
1st. Chamber Temperature |
800 ℃–– -1000 ℃ |
|
second. Chamber Temperature |
1000 ℃ -1200 ℃ |
|
Residency Time |
2.0 Sec. |
|
Gross Weight |
1500kg |
|
Exterior Measurements |
140x90x120cm |
Tel: +86-25-8461 0201
Website: www.hiclover.com
Email: [email protected]
Email: [email protected]
2020-06-30
Edificio de la casa del incinerador "
Casa incineradora para el modelo TS50
Installation et mise en service de crémation de chien et de chat de famille d'incinérateur mobile conteneurisé à double chambre de combustion
Chambre de combustion double
Conception de tous les incinérateurs de déchets avec double chambre de combustion. Haute température, traitement de la fumée, pas de fumée noire, respectueux de l’environnement.
Incinérateur mobile conteneurisé
L’incinérateur est monté dans un conteneur ISO avant de quitter l’usine, installation libre, pas de construction de maison d’incinération, mobile par camion.
Crémation pour chiens et chats en famille
Conception spéciale avec plate-forme mobile, matériau de la chambre de combustion et sur mesure pour les entreprises de crémation pour animaux de compagnie
Installation et mise en service
Les ingénieurs de Clover installent, forment pour la majeure partie de la région et forment gratuitement dans notre usine.
animal waste incinerator
secondary chamber
1000 degree
chimney
standard
shredder
separately
Autoclave or microwaves
separately
temperature monitor
attached outside of machine
operating
Fuel and electric
During the start and end incineration operations at the waste incineration plant the temperature shall be maintained
at 850 °C, while it shall be 1100 °C when incinerating dangerous waste containing halogenated organic substances with
content of chlorine or its compounds. The temperature shall be maintained at 1000 °C during incineration of medical
waste.
MUNICIPAL SOLID WASTE INCINERATORS
Municipal waste incinerator quantities and capacities shall be designed for 24-hour 7-day-a-week continuous operation.
Incinerators shall be capable of processing both wet and dry material and operating on either diesel fuel, JP-8 fuel,
or waste oil; see Plumbing for fuel storage system requirements. The following shall be provided as a minimum:
Reinforced concrete mounting foundations, feed or charging hoppers (or loaders), primary combustion chambers
with ash cleanout doors, secondary combustion chambers with ash cleanout doors, cyclone air filters (or separators),
Waste Incineration HICLOVER Model TS75
Waste Incineration HICLOVER Model TS75
Items/Model
TS75( PLC)
Picture
![]()
Principle
Waste Incineration
Burn Price
Average 75 kg/hour
Feed Ability
Typical 150kg
Control Setting
PLC( Programmable Reasoning Controller Incinerator)
Burning Chamber
770L
Inner Measurements
100x81x95cm
Second Chamber
385L
Smoke Filter Chamber
Yes
Feed Mode
Handbook
Voltage
220V
Power
0.7 Kw
Oil Consumption (kg/hour)
Typical 16.9
Gas Consumption (m3/hour)
***
Temperature Level Monitor
Digital Display
Temperature Level Security
Yes
Oil Storage Tank
100L
Feed Door
99x91cm
Smokeshaft
3Meter
Smokeshaft Type
Stainless-steel
1st. Chamber Temperature Level
800 ℃–– -1000 ℃
2nd. Chamber Temperature
1000 ℃ -1200 ℃
Residency Time
2.0 Sec.
Gross Weight
4500kg
External Measurements
2.30 mx1.30 mx2.55 m
Incinirator of Veterinary Hospital
Basic Info.
Product Description
Technology Respond(FAQ)
Q: What is kind of waste can utilize within this gear? A: This gear for medical waste, pet animal, Municipal waste, live waste. Prohibit any radiation and volatile substance, liquid waste and gas waste.
Q: Incinerator Smoke Standard A: China Government Standard: No. GB18484-2001. Incinerator price, incinerator price for 50kg/hr produced in china, incinerator manufacturers, incinerator small scale, incinerator suppliers in china, incinerator baths china, The animal/pet combustion rate around 2/3 of average capacity.
Clover incinerator utilize time per day up to 24 hours. Between each feed/combustion time, there are about 0.5-1 hours cooling time and time for feeding waste. Actual combustion time per day is about 16 hours. The lifetime of incinerator between 5-10 year based on utilize.
Ordinarily, we proposition little laboratory, little clinic use capacity under 20 kgs per hour. When incinerator use in hospital, please calculate the waste output capacity around 2kgs per individuals every day. If there are 200 sickbed in the hospital, which ‘s mean you need 1 incinerator capacity around 400kgs every day, switch to capacity per hour is around 30-40 kgs per hour. According the operation time every day, waste material, budget, development, etc, you can use capacity from 30-50 kgs per hour incinerator. *How to calculate Animal Cremation Burn Rate: 2/3 of the medical waste.
Q: Meeting and Testing A: We supply all files and incinerators easy to installation and functionality. Client can send individuals visit our factory to find out operation and installation. Generally, We do not send engineer to local website if not request. The dispatch cost is extra based on order. The next combustion chamber: 1000-1200 centi degree.
Q: Incinerator Control Mode A: Default Control manner is common control instance. PLC mode based on model and order.
Q: Operation and maintenance costs A: Operation cost based on fuel consumption rate and power/staff, etc.
Annual around $500-$1000USD per year maintenance according version, utilize situation.
One individual can service 02 unit incinerators. The team should have basic electrician understanding to operate/inspect/maintaince incinerator/burner/blower based on operation user guider, and know threat of medical waste to protect worker self with essential protection component.
One person can service 02 unit incinerators. The staff should have basic electrician knowledge to operate/inspect/maintaince incinerator/burner/blower according to operation user guider, and know risk of medical waste to protect worker self with necessary protection element.
Q: The Residency time in secondary combustion chamber
A: 02 sec.
| Items/Model | TS10(PLC) | TS20(PLC) | TS30(PLC) | TS50(PLC) | TS100(PLC) |
| Burn Rate | 10 kg/hour | 20 kg/hour | 30 kg/hour | 50 kg/hour | 100 kg/hour |
| Feed Capacity | 20kg | 40kg | 60kg | 100kg | 200 kg |
| Control Mode | PLC | PLC | PLC | PLC | PLC |
| Combustion Chamber | 100L | 210L | 330L | 560L | 1200L |
| Internal Dimensions | 50x50x40cm | 65x65x50cm | 75x75x60cm | 100x80x70cm | 120x100x100cm |
| Secondary Chamber | 50L | 110L | 180L | 280L | 600L |
| Smoke Filter Chamber | Yes | Yes | Yes | Yes | Yes |
| Feed Mode | Manual | Manual | Manual | Manual | Manual |
| Voltage | 220V | 220V | 220V | 220V | 220V |
| Power | 0.5Kw | 0.5Kw | 0.5Kw | 0.7Kw | 0.7Kw |
| Oil Consumption (kg/hour) | 5.4–12.6 | 7.8–16.3 | 10.2–20 | 12.1–24 | 14–28 |
| Gas Consumption (m3/hour) | 6.2–11.4 | 8–15.7 | 9.8–20 | 9.9–26.1 | 10–32.2 |
| Temperature Monitor | Yes | Yes | Yes | Yes | Yes |
| Temperature Protection | Yes | Yes | Yes | Yes | Yes |
| Oil Tank | 100L | 100L | 100L | 100L | 200L |
| Feed Door | 30x30cm | 45x40cm | 55x50cm | 70x55cm | 80x60cm |
| Chimney | 3Meter | 3Meter | 5Meter | 5Meter | 10Meter |
| Chimney Type | Stainless Steel | Stainless Steel | Stainless Steel | Stainless Steel | Stainless Steel |
| Residency Time | 2.0 Sec. | 2.0 Sec. | 2.0 Sec. | 2.0 Sec. | 2.0 Sec. |
| Gross Weight | 1500kg | 2200kg | 3000kg | 4500kg | 6000kg |
| External Dimensions | 140x90x120cm | 160x110x130cm | 175x120x140cm | 230x130x155cm | 260x150x180cm |
Скорость 30 кг 60 кг подача нефти и газа горелка небольшой мусоросжигательный завод

|
Машина За работой Режим |
Масло или же Газ + Мощность |
|
Напряжение |
220В |
|
Масло потребление (л / час) |
В среднем 13,3лит / час / камера |
|
Газ потребление (NG) (м3 / час) |
16.0 (м3 / час) (НГ) |
|
Газ потребление (Сжиженный нефтяной газ) (м3 / час) |
11,7 (м3 / час) (Сжиженный нефтяной газ) |
|
Горение показатель |
В среднем 30кг/час |
|
Кормить Режим |
Руководство по эксплуатации |
|
Начальный Горение камера |
360 литров |
|
Вторичный Горение камера |
200 литров |
|
Горение Камера Материал |
Огнеупорный Конкретный Цемент + огнеупорный кирпич |
|
Внутренний Габаритные размеры |
да (Начальный камера) |
|
Внешний Габаритные размеры |
210x120x 210см(без камин) |
|
Дверь открытие |
48X 60 см |
|
Топливо Тип |
Дизель Нефть / природный газ / сжиженный газ |
|
Горелка |
Оригинал |
|
Камин длина |
13,0 Метры |
|
Дым фильтр камера |
да |
|
Температура монитор |
Два рисунок Цифровой дисплей |
|
Температура защита |
да |
|
Масло бак |
200л |
|
Горение Эффективность |
> 98% |
|
Камин тип |
Нержавеющая стали |
|
1-й. температура в камере |
800c– 1000c |
|
2-я камера температура |
1000c– 1200c |
|
Резиденция время |
2,0 сек. |
|
Валовой масса |
4000кг |
|
Электрические Пластик а также очки Измельчитель |
да |
|
Скруббер |
да |
|
Гарантия Период |
1 год |
|
Начальный горение камера |
да |
|
Вторичный горение камера |
да |
|
Мусоросжигатель контроль дело |
С. стали |
|
Мусоросжигатель камин |
Оригинал |
|
Топливо Горелка |
да |
|
Масло танк вместимость |
да |
|
Опора масляного стенда |
да |
|
Сухой Дым Фильтр Камера |
да |
|
Воздушный вентилятор |
да |
|
Общее трата сжигание емкость / время |
Минимум 60 кг |
для Министерства здравоохранения, Кабул, Афганистан
Телефон: + 86-25-8461 0201
Сайт: www.hiclover.com
Электронная почта: [электронная почта защищена]
Электронная почта: [электронная почта защищена]
2020-06-30






